HOME>PRODUCTS>MECHA-LOCK>Operational Notes and Precautions

MECHA-LOCK

High precision Mecha-lock

MC

MA·MSA·MKA

MB

MT·MKT

MR

MN·MKN

Operational Notes and Precautions

Please be sure to completely read the following precautions in order to be able to safely use ISEL products and make the most effective use of the products and get all possible product advantages and performance.

Before starting use, make sure you have read this Instruction Manual carefully and follow the instructions contained in it.
The Instruction Manual should always be kept in a convenient location that allows operators to consult it for reference.

Safety-related notes

In this Instruction Manual, important precautions are found in "Danger" and "Caution" categories.

Dnager : Misuse can cause injury or death.   Misuse can cause injury or death.


Caution : Operational difficulties may result or equipment can be damaged by incorrect use.   Operational difficulties may result or equipment can be damaged by incorrect use.


1.Design Selection Notes

Make sure a safety cover is installed.

Dnager : Misuse can cause injury or death.
To prevent injury to the fingers or hand during operation through inadvertent insertion, please install the safety cover.

Make sure to install a safety device.

Dnager : Misuse can cause injury or death.
The drive shaft and driven shaft may separate if the products have been damaged. To guard against this, please install a safety device such as a safety brake for protection. The machine should not be in operation when the safety cover is open.

Do not exceed recommended torque.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
Machinery can be damaged when products are used with torque exceeding the recommended range. The products must not be used with excessive torque.

2.Installation-related Notes

Do not power on the machinery.

Dnager : Misuse can cause injury or death.
A dangerous situation may result during the uninstallation procedure if the machinery accidentally starts. Please confirm the main power to the machinery is turned off.

Make sure all screws and bolts are fully tightened.

Dnager : Misuse can cause injury or death.
Damage to products, inability to meet specifications and dangerous situations can result if bolts and screws are not fully tightened. Make use of a torque wrench and tighten to the recommended torque.

Do not use any non-manufacturer authorized screws, bolts etc.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
Loose parts can cause damage. Confirm only authorized parts are used.

Only use products to their maximum recommended allowed capacity.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
Our installed products should only be used to their maximum allowable capacity.
If used over the maximum allowable capacity, damage to the machinery or other problems may result.

Use protective equipment.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
For safe operation, safety glasses and gloves should always be used during installation/operation.

3. Operation Notes

Do not touch any product during operation.

Dnager : Misuse can cause injury or death.
Any contact with rotating parts can result in injury to fingers or hand. Do not touch operating products.

Do not exceed recommended rotation speed.

Dnager : Misuse can cause injury or death.
Damage and danger may result if excessive rotational speeds are used. Use the coupling below the maximum allowed rotational speeds.

Do not operate when slippage occurs.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
As products can retain heat, they can cause slippage. Operation should be stopped when slippage occurs.

Stop operation if vibration or noise is present.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
Improper installation can cause vibration and/or noise. If operation continues in this condition, damage may result to the machinery. Loose screws can also cause noise and vibration as well as improper installation.

Do not operate in conditions that can affect products.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
Avoid operation in conditions that can affect products. These include use in rusty areas, use involving chemicals, excessive high/low temperatures and other similar conditions.

4. Inspection Notes

Make sure power is off.

Dnager : Misuse can cause injury or death.
When removing a product from the machinery, danger may occur if the machinery accidentally starts. Make sure the main power to the machinery has been switched off before any contact with it.

Do not modify any ISEL components in any way.

Dnager : Misuse can cause injury or death.
ISEL is not responsible for any damage caused by unauthorized modification or repair to its products.

Do not handle product immediately after stopping operation.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.
During operation, products reach a high temperature that can cause injury.
Allow time for cooling and test before handling.

5. Disposal Notes

Products should only be disposed of by authorized personnel for reasons of environmental protection.

Caution : Operational difficulties may result or equipment can be damaged by incorrect use.